1. Home
  2. News & Insights
  3. Mooring Equipment Does Not Fail All at Once: Rope Fatigue, Fender Ageing and Winch Brake Safety

Industry note

Mooring Equipment Does Not Fail All at Once: Rope Fatigue, Fender Ageing and Winch Brake Safety

Mooring is one of the few shipboard operations where stored energy, heavy hardware and people share the same small space. A line under tension holds energy that is released if it parts; a fender absorbs energy that would otherwise go into a hull; a winch brake decides which of those happens. All three degrade slowly and quietly. The useful engineering question is therefore not how old a component is, but what it has been asked to do and what inspection can actually see. The published evidence on rope fatigue, rubber fender ageing and winch brake behaviour supports a condition- and history-based approach to replacement rather than a purely calendar-based one.

Why calendar age is a weak predictor

A mooring line, a fender and a brake band fail by different mechanisms, but they share one property: damage is cumulative and largely internal until it becomes visible.

ComponentDominant degradation mechanismInspection question
Synthetic mooring lineTension fatigue, creep, abrasion, heat and ultraviolet exposureWhat load history and how many cycles has it seen, and has residual strength been assessed?
Rubber fenderRubber ageing, crack growth, permanent deformation, changed reaction forceHow does it behave in compression now, not only when new?
Mooring winch brakeBand wear and adjustment, friction stability, setting driftDoes it still render at the intended load, and when was that verified?

Rope fatigue: load history, not calendar age

Synthetic fibre ropes are not one material with one failure mode. High-modulus polyethylene (HMPE) ropes provide high strength at low weight but are comparatively sensitive to sustained load, heat and abrasion, while polyester and nylon trade some strength for elongation and energy absorption. The common factor is that load history, meaning how often, how hard and over what range a line has been cycled, drives strength loss far more than the number of years in service. Humeau and colleagues addressed this by developing tension fatigue failure prediction for HMPE fibre ropes (Humeau et al., 2018). The paper's contribution is the prediction method itself; for an operator, the existence of such methods is the reminder that remaining strength is treated as a function of accumulated load history rather than calendar age.

Modelling choices matter as much as inspection. Sørum and colleagues examined synthetic fibre rope stiffness in mooring analysis for floating offshore wind turbines and note that it is both load-history and load-rate dependent: slow loading gives a quasi-static stiffness, while rapid cyclic loading gives a higher dynamic stiffness (Sørum et al., 2023). Comparing a model that accounts for quasi-static and permanent elongation with bi-linear models used in dynamic analysis, they found that the bi-linear approach artificially reduced tension ranges, particularly where the difference between the two stiffnesses is large, and therefore predicted a longer fatigue life. Permanent elongation also changed extreme-load predictions, and the simplified model introduced an amplitude dependence in horizontal natural periods. Anyone relying on a fatigue-life calculation should ask which stiffness model produced it, because a longer predicted life is not automatically a safer one.

That is why condition-based inspection intervals are more defensible than fixed ones. A line that has spent a season on a berth with a long swell fetch, or that has worked as a spring line in a strong current, has a different history from one that has mostly been slack. External inspection can find abrasion, glazing, broken or fused yarns and localised stiffness changes, but internal filament fatigue has no reliable visual signature. Where records are thin, the prudent response is earlier retirement or more conservative assessment, not a longer interval.

Rubber fenders: ageing from the inside out

Rubber marine fenders are usually bought as long-life assets, and the evidence broadly supports that expectation, with qualifications. Akiyama and colleagues investigated the service years of large circular-shaped buckling (CSB) fenders with panel contact, using supply records and compression and material tests on fenders returned from ports (Akiyama et al., 2017). The recorded actual service life ranged from 15 to 35 years. Compression tests showed that reaction forces increased moderately with years in service, and beyond visible cracks and deformation the tests found invisible signs of ageing: uneven buckling, increased reaction force and crack growth.

The material results were partly reassuring. Deterioration of physical properties was limited to the rubber surface, and the centre of the rubber bodies was still considered elastic and flexible. But the first compression cycle of a used fender produced a higher reaction force than the catalogue value, which corresponds to the average of the second and third cycles. The authors flag that this could matter if a used fender is kept as inventory stock, because the berth structure or the vessel's hull may see a stiffer response than the design assumed. For a buyer, the consequences are that age alone is a poor retirement criterion, that condition and behaviour in compression matter, and that stored spares should be treated as ageing hardware with their own history rather than as new equipment.

Winch brakes: holding versus rendering

A mooring winch brake has two jobs that are easy to confuse. It must hold a line at a set load, and it should render, paying out under controlled slip, before the line's own breaking load is reached, so that an overload is shed rather than stored until something parts. Iglesias-Baniela and colleagues analyse accident reports involving large vessels in mooring operations or breaking away from moorings, which concluded that winch brakes did not render before line parts, and explain why the margin between brake holding capacity (BHC) and minimum breaking load (MBL) is a safety function rather than a tuning preference (Iglesias-Baniela et al., 2020). If the brake can hold more than the line can take, the line becomes the weakest link and the brake stops being a protective device.

The paper examines reliability concerns with conventional screw-type, manually applied band brakes and argues that spring-applied band brakes, with manual setting and release or with hydraulic release, are a safer arrangement. It also describes a typical procedure for brake testing a liquefied natural gas (LNG) ship's winch with a hydraulic jack, fixing the BHC so that it holds 60% of the MBL of the mooring line. Whatever figures a particular vessel uses, the structure of the requirement is the same: the brake setting must be deliberately established, verified and recorded, and revisited as bands wear and lines are replaced. A brake that passed a test several line changes ago is not evidence about today's configuration.

Accident evidence and the design response

Recurring accidents are why brake behaviour and line condition attract attention. Gao and colleagues review frequent mooring broken-cable accidents around the world, analyse the state of port ship mooring operations, and describe an intelligent mooring system that combines cable and fender functions, adapting to the ship's six-degree-of-freedom motion, monitoring load data and applying active control through follow-up and damping (Gao et al., 2021). Whether or not such systems become standard, the design direction points the same way as the inspection argument: measure the loads, understand the motion, and do not assume hardware will behave as specified indefinitely. Lee and colleagues provide the complementary case-based view, presenting a failure analysis of a naval vessel's mooring system with suggestions for reducing line tension under ocean wave excitation (Lee et al., 2015).

Read together, this literature frames mooring risk as a system problem: line tension depends on berth geometry, wave and current excitation, winch settings and operator decisions, and a single component can be blamed after the fact for a load path it did not create alone.

Practical checks for buyers and operators

The evidence converts into a short set of records, criteria and tests that can be specified before hardware is ordered or accepted.

  • Line history. Record installation date, service (berth, line position, tension setting), cycles and inspections, and retire on condition as well as age.
  • Inspection criteria. Define what is unacceptable, including abrasion depth, glazing, broken or fused yarns, stiffness change and twist, and train inspectors to apply the same criteria consistently.
  • Retirement decisions. When history is unknown, shorten the interval or derate rather than averaging an unknown line into a fleet figure.
  • Fender condition and age records. Inspect for cracks, deformation and uneven buckling, treat stored spares as ageing items, and ask how a used fender's first-cycle reaction force compares with its catalogue value.
  • Brake setting and test. Establish BHC against MBL deliberately, test at a defined interval, and record results whenever lines or bands change.
  • Spares and tails. Keep spare lines and tail ropes with their own records and check compatibility with the drum and brake.
  • Training and procedures. Make sure crews understand rendering behaviour, snap-back zones and the actions to take when a line is overloaded.

For deck and mooring equipment buyers, these checks become specification and documentation questions rather than product features alone. When comparing a mooring winch or a windlass, brake rating, test method and maintenance information are as important as headline capacity, and the same applies when lines and fenders are specified alongside the equipment. The deck and mooring equipment category is best read as a system of line, winch, brake, fender and berth, because that is how the loads travel.

References

  1. Akiyama, H., Shimizu, K., Ueda, S., & Kamada, T. (2017). Investigation on service years of large rubber marine fenders. Journal of JSCE, 5(1), 392-401. https://doi.org/10.2208/journalofjsce.5.1_392
  2. Gao, F., Hu, K., Shen, W.-J., & Li, Y. (2021). Study on the safety guarantee of ship mooring from frequent cable accidents. IOP Conference Series: Earth and Environmental Science, 621(1), 012007. https://doi.org/10.1088/1755-1315/621/1/012007
  3. Humeau, C., Davies, P., Smeets, P., Engels, T. A. P., Govaert, L. E., Vlasblom, M., & Jacquemin, F. (2018). Tension fatigue failure prediction for HMPE fibre ropes. Polymer Testing, 65, 497-504. https://doi.org/10.1016/j.polymertesting.2017.12.014
  4. Iglesias-Baniela, S., Pérez-Canosa, J. M., & Cid-Bacorelle, D. (2020). Spring-loaded winch band brakes as tools to improve safety during mooring operations on ships. TransNav, the International Journal on Marine Navigation and Safety of Sea Transportation, 14(3), 711-719. https://doi.org/10.12716/1001.14.03.25
  5. Lee, K.-H., Han, H.-S., & Park, S. (2015). Failure analysis of naval vessel's mooring system and suggestion of reducing mooring line tension under ocean wave excitation. Engineering Failure Analysis, 57, 296-309. https://doi.org/10.1016/j.engfailanal.2015.08.005
  6. Sørum, S. H., Fonseca, N., Kent, M., & Faria, R. P. (2023). Modelling of synthetic fibre rope mooring for floating offshore wind turbines. Journal of Marine Science and Engineering, 11(1), 193. https://doi.org/10.3390/jmse11010193